克鲁勃GH 6-320合成齿轮油 深圳市深鹏孚润滑油有限公司 0755-28130719
张明:18902852991(微信同号)何经理:15919727128(微信同号)欢迎您来电咨询价格!
Klübersynth® GH 6 oils
Synthetic gear and high temperature oils Klübersynth GH 6-32, 46, 80, 100, 150,
220, 320, 460, 680, 1000 Edition 05.08, replaces edition 11.06 Article
numbers: 012157/012009/012158/012159/012160/012161/012162/012163/012164/012165,
012281 en MA-TM/HSi Benefits for your application • The oils meet the
requirements according to DIN 51 517 – 03, CLP. Corresponding gears can
be switched to Klübersynth GH 6 oils without prior consultation with
the gear manufacturer provided the general application notes are observed. • As
of ISO VG 220 the scuffing load stage API GL 5 is achieved. Gears are
sufficiently protected against scuffing even under high peak loads. • Much
longer service life than mineral oils due to the excellent ageing and
oxidation resistance of the base oil; thus maintenance intervals can be
extended and in certain cases even lifetime lubrication is possible • Owing to
the wide service temperature range a single viscosity grade can cover both low
and high temperatures in many applications • The optimum friction behaviour of
the polyglycol base oil reduces power losses and improves efficiency •
The good wear protection of both gears and rolling bearings ensures that the
service life calculated for the lubricated components is achieved • The
excellent viscosity-temperature behaviour supports the formation of a sufficient
lubricating film even at elevated and high temperatures • Seals made of 72 NBR
902, 75 FKM 585 and 75 FKM 170055 are resistant Klübersynth GH 6 oils. Leakage
and contamination are prevented. • Approved by Flender, SEW Eurodrive,
Getriebebau Nord, Stöber Antriebstechnik, Lenze, ZAE Antriebstechnik,
Bonfiglioli, Rossi Motoriduttori, Motovario, Moventas, etc. Description
Klübersynth GH 6 oils are gear oils on a polyglycol basis. They have a high
scuffing load capacity and micro-pitting resistance. These oils have also proved
their good wear protection in rolling bearings on the FAG FE 8 test rig for gear
oils. Klübersynth GH 6 oils stand out for their excellent ageing and oxidation
resistance, good viscosity-temperature behaviour and very good thermal
stability. Application Klübersynth GH 6 oils were especially developed for the
lubrication of worm gears with steel/bronze pairings. The polyglycol
base oils and special additives reduce the friction coefficient and
provide low wear values, which is a clear advantage in these applications.
Klübersynth GH 6 oils achieve a particularly low wear intensity according to DIN
3996 (calculation of load capacity of worm gears). Klübersynth GH 6 oils are
also used for the lubrication of bevel and spur gears, rolling and plain
bearings as well as all types of denture couplings, especially when exposed to
high temperatures. Klübersynth GH 6 oils can also be used for the lubrication of
lifting, drive and transport chains. Product information Klübersynth® GH 6 oils
Synthetic gear and high temperature oils Klübersynth GH 6-32, 46, 80, 100, 150,
220, 320, 460, 680, 1000 Edition 05.08, replaces edition 11.06 Article numbers:
012157/012009/012158/012159/012160/012161/012162/012163/012164/012165/012281 en
MA-TM/HSi Application notes Klübersynth GH 6 oils can be applied by immersion,
immersion/circulation and injection. Klübersynth GH 6 oils are not miscible with
mineral oils and synthetic hydrocarbons. We recommend cleaning the lubrication
points or rinsing gears with the Klübersynth GH 6 oil which will be used after
conversion. Klübersynth GH 6 oils are neutral towards ferrous metals
and almost all nonferrous metals. There may be increased wear
when the contact surfaces of design elements made of aluminium or
aluminium alloys are exposed to dynamic loads. If necessary, preliminary tests
should be carried out. For permanent temperatures up to 80 °C seals made of 72
NBR 902 may be used. For higher temperatures, we recommend to use seals made of
75 FKM 585 or 75 FKM 170055. It should be noted that elastomers from one or
several manufacturers can behave differently; therefore tests should be
performed. When applying Klübersynth GH 6 oils we recommend the use of
two-component paints (reaction paints) for interior coating. Oil gauge
glasses should preferably be made of natural glass or polyamide materials. Other
transparent plastics, e.g. Plexiglas, have a tendency to crack under stress. The
suitability of materials used in contact with Klübersynth GH 6 oils
should be tested, especially prior to series application. Viscosity
selection When determining the oil viscosity for gears, the
manufacturer's instructions take priority. In cases where there are no
gear manufacturer's instructions, the viscosity can be selected in accordance
with the enclosed worksheet "Klübersynth GH 6 oils – selection of oil viscosity
for gears". To determine the correct oil viscosity for bearings, please observe
the bearing manufacturer's instructions. For determining the actual viscosity,
please refer to the enclosed viscosity-temperature diagram indicating the
differing viscositytemperature behavior of Klübersynth GH 6 oils as compared to
mineral oils. Minimum shelf life The minimum shelf life is approx. 36
months if the product is stored in its unopened original
container in a dry, frost-free place. Pack sizes 20 l canister 200 l
drum Material Safety Data Sheets Material safety data sheets can be downloaded
or requested via our website www.klueber.com. You may also obtain them through
your contact person at Klüber Lubrication. Product information
Klübersynth® GH 6 oils Synthetic gear and high temperature oils Klübersynth GH
6-32, 46, 80, 100, 150, 220, 320, 460, 680, 1000 Edition 05.08, replaces edition
11.06 Article numbers: 012157, 012009, 012158,012159, 012160, 012161, 012162,
012163, 012164, 012165, 012281 en MA-TM/HSi Product data Klübersynth GH 6- … 32
46 80 100 150 220 320 460 680 1000 1500 ISO VG DIN 51 519 32 46 – 100 150 220
320 460 680 1000 1500 Density, DIN 51 757, at 15 °C, [kg/m³], approx. 984 1035
1040 1043 1050 1060 1067 1074 1075 1075 1080 Kinematic viscosity, DIN 51 561 at
20 °C, [mm2 /s], approx. at 40 °C, [mm2 /s], approx. at 100 °C, [mm2 /s],
approx. 88 32 6,5 113 46 9 205 80 15 270 100 20 400 150 29 630 220 40 880 320 54
1240 460 71 1900 680 110 3000 1000 167 4300 1500 231 Viscosity index, DIN ISO
2909 > 150 > 190 > 190 > 190 > 210 > 220 > 220 > 220
> 220 ≥250 > 250 Flash point COC, DIN ISO 2592, [°C] > 220 > 250
> 250 > 250 > 250 > 250 > 250 > 250 > 250 ≥250 > 250
Pour point, DIN ISO 3016, [°C] < -45 < -40 < -40 < -35 < -35 < -35 < -30 < -25 < -25 ≤-25 < -10 Foaming characteristics, ASTM D 892, sequence I, II und III, [ml] < 100/10 Copper corrosion, DIN EN 2160, 24h, corrosion rating 1 – 100 Corrosion protection on steel, DIN ISO 7120 0 – A Ageing characteristics, ASTM D 2893, increase in viscosity, [%] ≤ 6 FZG gear test rig, A/8.3/90, DIN 51354-2, scuffing load stage > 14 API scuffing load
capacity API GL 5 Rolling bearing test rig FE 8, D 7,5/80-80, DIN 51 819-3, wear
of rolling elements, [mg] wear of cage [mg] ≤ 30 ≤ 200 Service temperature
range*, [°C] -45 to 160 -40 to 160 -35 to 160 -30 to 160 -25 to 160 -25 to 160
-10 to 160 * Service temperatures are guide values which depend on the
lubricant's composition, the intended use and the application method. Lubricants
change their consistency, apparent dynamic viscosity or viscosity depending on
the mechano-dynamical loads, time, pressure and temperature. These changes in
product characteristics may affect the function of a component. Product
information Klübersynth® GH 6 oils Synthetic gear and high temperature oils
Lubrication is our world With more than 2000 products available around the
world, you can be sure that Klüber has the right product for your application.
Please contact Klüber Lubrication specialists worldwide to assist you
in all matters regarding lubrication. www.klueber.com Klüber Lubrication München
KG, Geisenhausenerstraße 7, 81379 München, Germany, phone +49 89 7876-0, fax +49
89 7876-333. The data in this product information is based on our
general experience and knowledge at the time of printing and is intended to give
information of possible applications to a reader with technical experience. It
constitutes neither an assurance of product properties nor does it
release the user from the obligation of performing preliminary tests with the
selected product. We recommend contacting our Technical
Consulting Staff to discuss your specific application. If required and
possible we will be pleased to provide a sample for testing. Klüber products are
continually improved. Therefore, Klüber Lubrication reserves the right
to change all the technical data in this product information at any time without
notice. Klüber Lubrication, a company of the Freudenberg Group Publisher and
Copyright: Klüber Lubrication München KG. Reprints, total or in part, are
permitted only prior consultation with Klüber Lubrication
München KG and if source is indicated and voucher copy is forwarded.
克鲁勃GH 6-320合成齿轮油
产品价格:面议
所 在 地:广东 - 深圳市
最小起订:1 桶
浏览次数:23748次
发布时间:2017-11-13 11:29 永不过期的信息
询盘时请说明在【亿商在线(yszx99.com)】看到的该产品信息!
负责声明:所展示的信息由供货商提供,内容的真实性、准确性和合法性由发布会员负责。【亿商在线(yszx99.com)】不承担任何责任。
友情提醒:为了您的交易安全,请尽量使用货到付款方式!如需要投诉,可进入"消费者防骗指南"了解投诉及处理流程,我们将竭诚为您服务!
负责声明:所展示的信息由供货商提供,内容的真实性、准确性和合法性由发布会员负责。【亿商在线(yszx99.com)】不承担任何责任。
友情提醒:为了您的交易安全,请尽量使用货到付款方式!如需要投诉,可进入"消费者防骗指南"了解投诉及处理流程,我们将竭诚为您服务!